Skip to content
Pakistan · China · UAEinfo@dsyndicate.co
LinkedInFacebook
Molten metal pouring from an induction furnace
Refractories · Steel

Choosing an Induction Furnace Lining: Silica, Neutral or Magnesia Ramming Mass

The ramming mass you choose decides how long your lining lasts, how often you stop to reline, and what each tonne of steel costs you.

TSThe Syndicate technical team
· 6 min read
In short
  • Silica is the economical choice for carbon steel and cast iron with acidic slag.
  • Neutral (alumina-magnesia spinel) suits alloy and stainless steel and plants that switch grades.
  • Magnesia handles basic slag, high manganese and the highest temperatures.
  • Judge a lining by cost per tonne of steel, not price per bag.

01What is ramming mass?

Ramming mass is a dry, granular refractory that forms the working lining of a coreless induction furnace. It is rammed or vibrated into place around a steel former, then heated so the grains sinter into a dense, hard layer.

That layer holds the molten metal and protects the coil behind it. It is also the part of the furnace that wears out. Every relining means downtime, labour and new material, so the right choice shows up directly in your cost per tonne.

Sparks from molten metal in a steel melt shop
The working lining sits between molten metal and the induction coil.

02The three types of ramming mass

Ramming masses are grouped by how they react with slag: acidic, neutral or basic.

SiO₂ > 97%

Silica

Acidic

High-purity quartzite with a small boric acid addition as sintering agent. The most widely used lining for melting scrap into billets and rebar.

Best forCarbon steel and cast iron, acidic slag
  • Lowest material cost
  • Easy to install
  • Good thermal shock resistance
  • Attacked by basic slag and high manganese
Al₂O₃ + MgO → spinel

Neutral

Spinel-forming

Alumina and magnesia react during sintering to form spinel, a mineral that resists both acidic and basic slag.

Best forAlloy and stainless steel, mixed grades
  • Higher temperature range
  • Wider slag resistance
  • Usually a longer campaign
  • Higher price; needs a correct sintering schedule
High-purity MgO

Magnesia

Basic

Based on high-purity magnesia. Stands up to basic slag and aggressive alloying elements better than any other lining.

Best forHigh-manganese, stainless and special alloys
  • Excellent basic-slag resistance
  • Very high temperatures
  • More sensitive to thermal shock
  • Must be kept dry before use

03Side-by-side comparison

SilicaNeutralMagnesia
Slag typeAcidicAcidic or basicBasic
Typical steelsCarbon steel, cast ironAlloy, stainless, mixed gradesHigh-Mn, stainless, special alloys
Temperature range
Slag resistance range
Thermal shock resistance
Material costLowestMediumHighest

Ratings are relative, for comparison only. Actual performance depends on the specific grade and your operating practice.

04How to choose the right lining

Start from what you melt, then check how you operate. Five questions settle most decisions.

  1. What steel grade do you produce?

    Plain carbon steel points to silica. Manganese, chromium or stainless points to neutral or magnesia.

  2. What is your slag chemistry?

    Lime-rich or manganese-rich slag attacks silica quickly. Match the lining to the slag, not the other way round.

  3. How hot do you tap, and how long do you hold?

    High tapping temperatures and long holding times favour neutral or magnesia linings.

  4. How is the furnace run?

    Continuous operation rewards a longer-lasting lining. Furnaces that stand cold between shifts suffer more thermal shock.

  5. What does a reline really cost you?

    Add material, labour and lost production. A dearer lining that lasts much longer can cost less overall.

Compare cost per tonne of steel, not price per bag.

05Installation matters as much as the material

Even the right ramming mass fails early if it is installed badly. Most premature failures trace back to a handful of causes.

Uneven rammingSoft spots and voids weaken the lining from day one.
Moisture in storageDamp material cracks and spalls during heat-up.
Wrong sintering scheduleToo fast, too slow or not followed at all.
Cold, heavy chargeThermal shock on a new lining from cold scrap.
Slag build-upSlag left on the walls between heats eats the lining.
Keep recordsTrack heats per lining to compare materials on real numbers.

06Frequently asked questions

Which ramming mass is best for an induction furnace making rebar billets?

For carbon steel billets melted from scrap, silica ramming mass is usually the most economical choice. If the charge carries high manganese, or the slag turns basic, a neutral lining is worth testing.

Can I switch from silica to neutral ramming mass?

Yes, at a full reline. Remove the old lining completely, then install and sinter the new material to its own schedule. Do not mix acidic and basic materials in one lining.

How many heats should a lining last?

It varies widely with furnace size, steel grade, temperature and operating practice. The useful figure is your own heats per lining and cost per tonne, tracked over several campaigns.

Silica · Neutral · Magnesia

Get the right ramming mass for your furnace

We supply ramming mass, castables and bricks for induction furnaces, ladles and tundishes from our refractory manufacturers, including Yingkou Shenghe Refractories and Zibo Long Keter. Share your furnace size, steel grade and current lining life, and we will recommend a grade with a manufacturer-backed offer.